Epoxy.com System #495
Elastomeric Urethane Pedestrian
Traffic Membrane
For Use Indoor, Outdoor and Direct Sunlight
Elastomeric Polyurethane System Description
Epoxy.com System #495 is an Elastomeric Urethane Membrane System, that is
liquid applied. System #495 Elastomeric Membrane System is seamless,
elastomeric (flexible), and UV. These qualities make it an excellent choice
for outside applications in direct sun and weather, where water tightness,
durability, and excellent appearance is required. Its elastomeric properties
will allow horizontal movements up to 1/8 inch without breaking.
Epoxy.com System #495 has excellent abrasion and chemical resistance.
The surface of System #495 can be varied to achieve the required anti-skid
and decorative look.
Elastomeric Polyurethane System Advantages
- Waterproof
- Elastomeric
- Resistant to Sunlight (UV)
- Safety (Anti-Skid)
- Epoxy.com System #495 is a system not just a single product so it
can be tailored to the specific needs of your application.
Elastomeric Polyurethane System Considerations
- All control joints must be properly installed, and carried
(revealed) to the surface of the system.
- Substrate must be properly prepared - see
Surface Preparation.
- Substrate temperature should be 60 degrees F. (absolute minimum of
55 degrees F required). If installation is to made at lower
temperature, the material will need a cold temperature cure.)
- On grade or below grade applications must have an effective moisture
vapor barrier under the slab.
- When the substrate has hydrostatic and/or moisture vapor
transmission issues they must be treated before the installation of
Epoxy.com System #495 Elastomeric Urethane Membrane System.
- Not for use in California
Typical Uses for the Elastomeric Polyurethane System
Epoxy.com System #495 Elastomeric Urethane Membrane System is ideal for:
- Raised Walkways
- Balconies
- Concrete and Wooden Decks
- Animal Housing and Cage Wash Areas
- Coolers
- Secondary Containment
- Docks and Ramps
- Garages laundries
- Locker Rooms
- Mechanical Equipment Rooms
- Pool Decks
- Showers
- Utility Rooms
- Any flooring/decking application that requires a durable, flexible,
waterproof, and attractive flooring/decking.
Technical Data - System Performance Properties
| Flammability |
ASTM D635 |
Self Extinguishing |
| Fungus & Bacteria Growth |
Mil-F-52505 § 4.4.2.11 |
Will not support growth of fungus or bacteria
when subjected to mildew and bacteria tests |
| Hardness |
ASTM D-2240 |
20-50 Shore D |
| Bond Strength to Concrete |
ACI COMM #403, Bulletin 59-43 |
300psi (100% Concrete Failure) |
| Resistance to Elevated Temperature |
Mil-D-3134F § 4.7.4 |
No slip or flow at required temperature of 158◦F |
| Coefficient of Friction |
ASTM D-2047 |
0.60 |
| Water Absorption |
ASTM D-570 |
Nil |
| Thermal Shock Resistance |
ASTM C-884 |
Passed |
| Abrasion Resistance |
ASTM D-4060 |
Will vary with finish |
| Impact Resistance |
Mil-D-3134F § 4.7.3 |
Withstands 16 ft./lbs. without cracking, chipping or
delamination. |
| Compressive Strength |
ASTM C-579, 7 days |
5000 psi |
| Tensile Strength |
ASTM C-307 |
1,200-1,500 |
| Thermal Coefficient of Expansion |
ASTM C-531 |
12-15 x 10-6 |
Membrane Performance Properties
| Ultimate Tensile Strength |
ASTM D-638 |
1,000-1,200 psi |
| Tensile Elongation |
ASTM D-638 |
350-400% |
| Hardness |
ASTM D-2250 |
80 Shore A |
Elastomeric Polyurethane Systems Maintenance
Clean with neutral soaps or detergents. Anti-skid floors typically use
periodic mechanical cleaning. Long period of heavy traffic may cause wear
patterns requiring a maintenance of the finish coat.
Elastomeric Polyurethane System Application
Typical system components and application rates are as follows:
-
Epoxy.com Product #899 Primer
applied at a rate of 250-300 SF per gallon
-
Epoxy.com Product #459 applied at a rate of 50 SF
per gallon (1st coat)
-
Epoxy.com Product #459 applied at a rate of 50 SF
per gallon (2nd coat)
-
Epoxy.com Product #77 broadcast into the wet send coat of
Product #459 at a rate of 1/2 lb per square foot
- Epoxy.com Product #467 applied in 2 coats at
a rate of 200 square feet per gallon per coat
For a complete set of installation instructions see
Elastomeric Decking System #495 Installation
Guide
or contact Epoxy.com Technical Support Department.
|
|
Proper mixing and installation is critical to the optimal success
of all product. See
Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over
350 products,
Since 1980
Florida & Vermont
USA
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com
714-657-3826 Technical Support
352-533-2167 Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
| We accept MasterCard, Visa, American Express, Discover, Wire Transfers, or
Cashier's Check. |
Copyright © 1994-2010 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
Unless
other wise agreed upon in writing, buyer is responsible for the cost of
shipping.
This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy.com a
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four
(4) months; Power Tools and Equipment 90 days; Vinyl Esters,
High Molecular Weight Methacrylates (HMMA) and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
|