Epoxy.com Product #701
Flexible Epoxy Gel Adhesive
DESCRIPTION:
Epoxy.com Product #701 Flexible Gel Adhesive is a two component, 100% solids, mixed at a 1:1 ratio
adhesive formulated to give a permanent bond to ceramic, metal, concrete and
elastomeric surfaces. Epoxy.com Product #701 Flexible Gel Adhesive is thixotropic, non-sag, and is
easily applied by trowel.
ADVANTAGES:
- Excellent bond to most substrates.
- Permanent flexibility, molecularly fixed, will not migrate.
- 100% solids, non-combustible.
- Thixotropic—Light Gel—Dependable gap filling adhesive for permanent adhesion of
structural components.
- Convenient one to one by volume mix ratio.
- Excellent chemical resistance.
- Excellent recovery from deformation by compression or elongation.
- Stays flexible at temperatures as low as -20° F (-29° C).
- Retains properties at temperatures as high as 300° F (149° C) in intermittent
exposure.
- Used by "Certified Applicators" to stop leaks between ceramic insulators and
transformer housing.
PHYSICAL PROPERTIES:
|
Color
|
Light Gray
|
|
Mix Ratio
|
1A:1B by volume
|
|
Viscosity
|
Light Gel
|
|
Gel Time (min.)
|
10 minutes @ 75° F (23° C)
|
|
Compressive Strength
ASTM C-579, Method B
|
3,000 psi min. - 7 days
|
|
Tensile Strength
ASTM D-638
|
1,350 psi min. - 7 days
|
|
Tensile Elongation (min.)
ASTM D-638
|
50% - 7 days
|
|
Lap Shear -
Steel to Steel
ASTM D-1002
|
800 psi min. - 7 days
|
SURFACE PREPARATION:
Surface must be clean. Remove grease, rust, or other foreign materials by best
means available. For best results surfaces should be dry during application.
MIXING:
Combine one part by volume of Component "A" with one part by volume of Component
"B". Mix for not less than (3) three minutes using a slow speed drill (300 to
600 rpm) and Epoxy.com-Mixing Paddle.
SHELF LIFE:
1 year
CAUTION:
WARNING! "A" Component contains epoxy resin. DANGER! "B" Component contains
alkaline amines; strong sensitizer. May cause skin sensitization or other
allergic responses. Use with good ventilation, particularly if material is
heated or sprayed. Prevent all contact with skin or eyes. Wear protective
clothing, goggles, gloves, and/or barrier creams. Keep containers closed when
not in use. Wash thoroughly after handling.
FIRST AID:
In case of skin contact, immediately wash with soap and water. In case of eye
contact, flush with copious amounts of water for at least (15) fifteen minutes.
Remove contaminated clothing. If irritation persists, seem medical attention.
Wash clothing before reuse.
FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN.
|
|
Proper mixing and installation is critical to the optimal success
of all product. See
Installation Tips,
Techdata, &
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
have.
For more information please contact:
Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Over
350 products,
Since 1980
Florida & Vermont
USA
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
sales@epoxy.com
714-657-3826 Technical Support
352-533-2167 Norm Lambert, President - Technical Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
www.epoxy.com
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
| We accept MasterCard, Visa, American Express, Discover, Wire Transfers, or
Cashier's Check. |
Copyright © 1994-2010 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
Unless
other wise agreed upon in writing, buyer is responsible for the cost of
shipping.
This
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
Epoxy.com a
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four
(4) months; Power Tools and Equipment 90 days; Vinyl Esters,
High Molecular Weight Methacrylates (HMMA) and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
|